ICONX - EXCAVATOR MMS185

$24.99
Metal Earth

Is a heavy construction equipment consisting of a boom, dipper, bucket and cab on a rotating platform known as the "house". The house sits atop an undercarriage with tracks or wheels. It is a natural progression from the steam shovel and often mistakenly called power shovel
2 Sheets


ICONX - F-14 TOMCAT™ MMS458

$31.99
Metal Earth

The supersonic F-14 Tomcat is a twin-engine, variable-sweep wing fighter aircraft. It was developed for the US Navy to counter Soviet MiG Fighter jets. The Tomcat is a two person crew consisting of a pilot in the front seat and a Radar Intercept Officer (RIO) in the back seat.
3 sheets of metal


ICONX - F-15 EAGLE MMS082

$11.99
Metal Earth

This twin engine tactical fighter was designed for the U.S. Air Force to gain and maintain air superiority in aerial combat. It first flew July 1972 and has become among the most successful modern fighter jets with over 100 aerial combat victories.
These amazingly detailed DIY models start as 4” square steel 3D models. Simply snip out the pieces and bend the tabs through corresponding connection points. Easy to follow instruction included. Tweezers or small needle nose pliers are suggested to facilitate assembly.
1 sheet of metal


ICONX - F-22 RAPTOR MMS050

$11.99
Metal Earth

The Lockheed Martin/Boeing F-22 Raptor is a single-seat, twin-engine fifth-generation super-maneuverable fighter aircraft that uses stealth, speed agility, precision and situational awareness, combined with air-to-air and air-to-ground combat capabilities, makes it the best overall fighter in the world today.
These amazingly detailed DIY models start as 4” square steel 3D models. Simply snip out the pieces and bend the tabs through corresponding connection points. Easy to follow instruction included. Tweezers or small needle nose pliers are suggested to facilitate assembly.
1 sheet of metal


ICONX - F-35A LIGHTING II MMS065

$11.99
Metal Earth

Is a family of single-seat, single-engine, fifth generation multirole fighters that are designed to perform ground attack, reconnaissance, and air defense missions with stealth capability. The F-35 has three main models; the F-35A employs conventional takeoff and landing, the F-35B will be used for short take-off and vertical-landings, and the F-35C will be carrier-based. The F-35 models are intended to provide the bulk of tactical airpower for the U.S. Air Force, Marine Corps and Navy over the coming decades.
These amazingly detailed DIY models start as 4” square steel 3D models. Simply snip out the pieces and bend the tabs through corresponding connection points. Easy to follow instruction included. Tweezers or small needle nose pliers are suggested to facilitate assembly.
1 sheet of metal


ICONX - F/A-18 SUPER HORNET™ MMS459

$32.99
Metal Earth

 

The F/A-18 Block III Super Hornet is the newest highly capable, affordable and available tactical aircraft in U.S. Navy inventory. The Super Hornet is the backbone of the U.S. Navy carrier air wing now and for decades to come.
3 sheets of metal


ICONX - F4U CORSAIR MMS035

$11.99
Metal Earth

The most capable carrier based fighter-bomber of World War II featured the largest engine available at the time: the 2,000 hp, 18-cylinder Pratt & Whitney R-2800 Double Wasp radial. It was the first US warplane to exceed 400 mph in level flight. The plane featured an unusual inverted gull wing to keep the undercarriage short while allowing the use of the large diameter propeller demanded by the powerful engine.
These amazingly detailed DIY models start as 4” square steel 3D models. Simply snip out the pieces and bend the tabs through corresponding connection points. Easy to follow instruction included. Tweezers or small needle nose pliers are suggested to facilitate assembly.
1 sheet of metal


 

ICONX - FARM TRACTOR MMS052

$16.99
Metal Earth

Is a simple open vehicle with two very large driving wheels on an axle below and slightly behind a single seat with the engine in front of the driver and two steerable wheels below the engine compartment. This basic design has remained unchanged for many years.
These amazingly detailed DIY models start as 4” square steel 3D models. Simply snip out the pieces and bend the tabs through corresponding connection points. Easy to follow instruction included. Tweezers or small needle nose pliers are suggested to facilitate assembly.
2 sheets of metal


Showing 46 to 54 of 180 (20 Pages )